This Episodes Questions: Brians Questions When making trivets, how to cut the grooves - when I cut mine I hogged out half the thickness of the wood in one pass. That led to some pretty rough cuts and gouges (i.e. scrap). I assume the answer is a router table with a lift, but of course I don’t have one YET. :) Also, what finish to put on a trivet (which is used for hot pans)? - different finish than a cutting board? Tung oil? Danish oil? I assume ’not’ ArmRSeal. Mark I’m preparing to build a set of kitchen cupboards from white oak. The style will be Mission, with some Frank Lloyd Wright Prairies Style touches. I have several questions. I have a SuperMax style cantilever 25-50 drum sander. Do you think that this is a feasible tool to level out the boards to remove the planer snipe? …and avoid having to cut 3” of the end of each piece? Darrin Guys Questions: Been enjoying your podcast through several projects. My background is homebuilding, but through my sawmill hobby and unwillingness to pay for overpriced garbage…I have found myself learning about woodworking. My question is about making doors. I have made one door so far using only groove cuts into the stiles’s and gluing the tenons of the rails and panels into these cuts. I don’t have much faith in the longevity of this door, but it’s been a year now. What is the traditional methodology for attaching the individual parts of a simple 3 panel door Should I just buy a domino and get it done… Also per your latest podcast episode, what is the best way to midi gate the wood movement at the joint of the rails/ stiles. As these joints are not small nor parallel. Sorry for the low brow question. Appreciate the knowledge. Lucas Hello esteemed woodworking gentlemen! Thanks for the amazing podcast and the contribution to the woodworking community. I’m seeking some general advice and hope you can help. I was recently watched a YouTube video where someone stated that a track saw blade should always be buried for the straightest possible cut. That made me wonder if I can be causing unnecessary blade deflection on my jobsite table saw and Dewalt miter saw. I often struggle achieving perfect 90 on those machines when crosscutting. As a hobbyist with limited shop time, setting up machines is pain but I understand its necessity. Can you speak on this blade deflection and are there any go to tricks that you have for ensuring your machines are set up properly? Thanks for any help you can provide.-Jose Huys Questions: A while back my wife and I bought and moved into a house with no dishwasher, then later purchased one after realizing how much not having one sucked. We made the mistake of assuming that we would be fine putting the dishwasher at the end of the counter, because we figured the top of the machine would look like a run-of-the-mill home appliance like a washer or dryer, rather than the monstrosity that it actually is. It is ugly. I think I actually recall my wife crying when she saw it, and not in a good way. Since then my loosely held plan has been finding a way to move or dispose of the contents of one section of our cabinets, then cut a section out of said cabinets big enough for the dishwasher to fit underneath. Recently, however, thanks in large part to your podcast, I have developed enough confidence in my woodworking skills to attempt a different idea. My thought is to make what is essentially an end cap or sidewall, which will match the existing cabinetry, anchor it somehow, and then place a new section of countertop between this end cap and the existing end cap of the cabinets. I would essentially be "extending" the countertop, thereby concealing top and visible side of the dishwasher. From what I can tell, all I would have to make, stain, and finish would be a cabinet side panel, a piece of trim to run along the bottom, and a partial face frame. So here come the questions: do you think this is doable, either generally or the way I am thinking? And what would be the easiest way to tackle this project? Note that I'm not particularly concerned over whether or not I use the same method of instruction as was used for the rest of the cabinetry. For example, I don't particularly care to use particle board with a veneer as the rest of the cabinets may have done if it would actually be easier or cheaper in this instance to just make the side panel out of a solid piece of wood. So long as it looks close, its fine with me. The applicable tools I can think of that I have at my disposal are a table saw with a crosscut sled, a compound miter saw, a jigsaw, fixed base router, various types of Sanders, a pocket hole jig, 15, 16, and 23 gauge nailers, and of course all of the basic hand tools. I would describe my skill level as approaching novice. Sincerely,Z achary T Owens Howdy yall, I'm wondering if you can recommend any smoke detectors or carbon monoxide detectors in the woodshop? I work out of a one car garage in Minnesota so have a gas heater to help me stay warm duri
