This Episodes Questions: Brians Questions: I recently bought a good amount of S3S ambrosia Maple from Rockler. I bought it at a crazy discount. The first time I picked some up they were selling it for $3 per board foot, and when I came in a few weeks later it had dropped to $1 per board foot. I asked multiple employees why the price was so low. They all said that they simply just didn't have room for the material. Looking around this seemed to be the case. I have been storing the wood in the loft of my shed/shop for several weeks now, which is cool and dry this time of year. I finally decided to begin a project using some of this material, but to my dismay I have discovered that most of the boards have a twist in them. I've been able to minimize this problem by strategically cutting the boards into smaller pieces, but when I put them in my crosscut sled, I've noticed that a few of the boards aren't even flat on the edge that is supposed to be jointed. Is this something I should expect after moving lumber that had been stored somewhere with moderate temperature and humidity to a cooler and dryer location? Or is it possible the store was selling this wood for so cheap because people had had issues with this material already? I try not to be overly fussy, especially when I've I've gotten a good deal on something, but this is one of the first times that I've purchased a significant amount of hardwood from a higher quality store and what I'm looking at is about the same quality I'd expect after picking out hardwood boards at random from a big box store. Lastly, considering that I don't have a joiner or a planer, is there any way for me to try to correct the twist in these boards? For now I just have worst of the boards clamped down to a flat surface. Thanks in advance for your time and your feedback. Sincerely, Zach Owens Hi guys, I have a question about how long does it takes, when working on a project, before "project fatigue" sets in? I woodwork for at least an hour or more everyday (much more on the weekends) and I have built book cases, a fancy cat tree, a hallway table, small boxes, solid oak doors, and shop furniture in the past year. Sometimes I get to the point where I just want to finish up the current project so I can start something new. It seems to happen around the 4 to 6 week mark. Do you ever get project fatigue? Just curious if I'm not alone. Also, thank you to Guy for discussing hide glue and shellac in previous podcasts. I'm now making my own glue and dissolving my own shellac flakes. I like the traditional aspect and easy of use. Cheers Chris from North Mankato, MN Guys Questions: I would like to build my kids a set of montessori style bookshelves out of solid maple, and I can see myself making more of these in the future for others. So, I am trying to figure out how to make the joinery fast, accurate and repeatable. Also, I would like to avoid using screws and I do not own a domino, so I think that probably makes dowels the best option? How would you make the 2 sides to this bookshelf? My thoughts are to make a template for the sides so I can route the shape. I am struggling with the dowels... Due to wood movement in the vertical shelf pieces, I was thinking about using 2 dowels, where one will be fixed and the other will have a slot cut into the side panel. See attached photos. Each horizontal shelf piece will be dadoed to the vertical shelf piece and the 4 shelves will not be connected to each other to help account for wood movement. If I use an mdf template for the sides and also put the dowel holes and slots in it, how would you cut the holes and slots? Router, router with bearing, drill press, hand drill? Is there a better way that could be easier or faster than I am missing? Thank you for all you help! Jeff Hello all! Thank you for a great show! About a year ago I built a cabinet with a cherry top. It was finished with a single coat Zinser Bulls Eye Seal Coat, followed by 3 coats of Poly. (wiped on). See original picture attached. Since then in a few places it developed small white spots. What would you recommend for me to do to fix it? Can I just apply a few more coats on top? If so, how would I prep the top? Or do I need to sand it back to bare wood? If so, what would be the process to sand it back? Bonus question, what could I have done to fail to prevent this? Max Huys Questions: 2. I remember a while back Huy mentioned buying a sewing machine and considering upholstery. Have you don’t anything with it? My wife has been on me for years to build a chaise lounge for our living room for a specific space, but even watching folks demonstrate the art I get a bit frazzled. I know Guy’s solution-just go buy the damn cushions. So, Guy, would you have your wife buy them first and build around them or build the piece (whatever it may be) and send her on a quest to find some to fit? Any resources for upholstery on wooden furniture? Peter Downing A few years ago I got some beautiful, large piec
